Home / Applications
Several patterns can be combined into a final design — slotted onto piling and built up course by course, on land or below the waterline.
Demountable construction
Most concrete structures are permanent for lack of an alternative — left unused or demolished once their job is done, at extra cost and waste. Aquacast is demountable by design: dismount, store and re-assemble elsewhere, with minimal environmental impact.
Pile, fit screw-bars, then slot casts into place — guided underwater until above water level.
Read → A.2Combat land erosion and movement; 90° supports resist the turnover effect on high walls.
Read → A.3Reinforce failing walls without demolition; reversed casts deflect wave force back to sea.
Read → A.4Polyurethane membranes between casts keep water out — or hold it in for reservoirs.
Read → A.5Reinforce existing banks or build new permanent structures — with height added later if needed.
Read → A.6Locate water breakers offshore to disperse force — combined with marinas, piers or platforms.
Read →
Construction of jetties
Once the size and nature of the construction are set, several patterns can be combined into the final design. Piles are installed to form the required pitch and the screw-bar fitted where needed; the casts are then slotted onto the piles. The water environment doesn't impede the work — casts are guided into location on the piles until the build rises above water level. The method is time-efficient and minimises material wastage.
Retaining walls
Several cast patterns suit retaining-wall construction, in a wide range of sizes and formations. As land is stripped for building or through deforestation, the threat of land movement is constant; piling can be set at an angle where required, and the resulting walls used as retainers — even to create stepped agricultural land.
On high walls the main challenge is the turnover effect of horizontal forces. A site survey and ground-density analysis set the piling depth and pitch tolerance, and foundation casts are made wider and thicker in proportion to wall height. Piling commences using the foundation slots as templates for accurate pitching, after which the remaining casts simply lower into position. To resist turnover, units can be assembled at 90° — forward and backward — giving extra rigid stabilisation, ideal for confined-space projects and for supporting existing defective walls.
Sea defences
Aquacast was developed to solve erosion by the battering force of waves and rising water levels. Where defences are weak or old sea walls can no longer withstand continuous impact, Aquacast reinforces the existing structure by piling in front or behind — without requiring demolition.
Working on the same interlocking principle, casts can be reversed and used together to form walls with deflecting angles that reflect wave force back toward the sea, greatly reducing impact.
Land reclamation
Land can be reclaimed from the sea with Aquacast products. Piling is carried out in the water or when the tide is out, following recommended procedures; casts are then used with polyurethane membranes sandwiched between them to keep water out. The same approach reverses to keep water in — as for reservoirs or water tanks. Sizes and functions depend on the application.
River banks & canals
The Aquacast system assembles quickly to reinforce existing banks or to build new, stronger, aesthetically pleasing permanent structures — with further height added later if required.
In October 2003, Aquacast International completed the Cornfield bridge retaining wall at Diggle, near Saddleworth, for Oldham Metropolitan Borough — serving three functions at once: stopping erosion, supporting the bridge loading, and holding the upper bank from sliding. After previous unsuccessful attempts, the wall was built using the Aquacast V-block system in 12 days, without adverse impact to the natural environment.
Where it's used
A wide range of sizes, designs and finishes makes the same system suitable across permanent structures and temporary works alike.
Coastal erosion
Conventional methods — piling beaches with stone or concrete pieces — take up considerable coastal surface, leaving disused beach and limited access, often unsightly enough to affect tourism and property values.
Aquacast believes the most efficient approach is to locate water breakers in the sea at recommended distances from the coast, dispersing water force and protecting against erosion. The principle of a marina, pier or platform can be incorporated into the same structure — achieving two objectives at once. Several design formations suit this application.